Pubblicazioni

Y. Gandhi, G. Minak (UNIBO), “A Review on Topology Optimization Strategies for Additively Manufactured Continuous Fiber-Reinforced Composite Structures”, Appl. Sci. 2022, 12(21), 11211; 

A. Piccininni, D. Sorgente, G. Palumbo (POLIBA) “GA-based optimization to control the thickness distribution in components manufactured via superplastic forming” Journal of Manufacturing Processes 2023, 86 (27), 126-135; 

L. Maragoni, P.A. Carraro, M. Simonetto, M. Quaresimin (UNIPD) "A novel method to include crack-induced delamination in a fatigue damage predictive procedure for composite laminates", Composites Science and Technology 238 (2023) 110011 

Mele, M. (UNIBO), Pisaneschi, G., Zucchelli, A. et al. Effects of short-loop material recycling on mechanical properties of parts by Arburg Plastic Freeforming. Prog Addit Manuf (2023).  

Mele, M. (UNIBO), Campana, G., Pisaneschi, G., De Martino, L. and Ricciarelli, M. (2023), "Dimensional accuracy and impact resistance of 3D printed clay reinforced with scrap polymer powder", Rapid Prototyping Journal, Vol. ahead-of-print No. ahead-of-print.  

Sandrini, G.; Gadola, M.; Chindamo, D.; Candela, A.; Magri, P.,  "Exploring the Impact of Vehicle Lightweighting in Terms of Energy Consumption: Analysis and Simulation" Energies 16(13), (2023) 5157

Minak, G. Solar Energy-Powered Boats: State of the Art and Perspectives. J. Mar. Sci. Eng. 2023, 11, 1519.   

Croccolo, D., De Agostinis, M., Fini, S. et al. Effects of infill temperature on the tensile properties and warping of 3D-printed polylactic acid. Prog Addit Manuf (2023).  

Schuster, V., Ciacci, L., Passarini, F., 2023. Mining the in-use stock of energy-transition materials for closed-loop e-mobility. Resources Policy, 86, Part B, 104155. 

A. Chiocca, M. Sgamma, F. Frendo, Closed-form solution for the Fatemi-Socie extended parameter in case of linear elasticity and proportional loading, Fatigue & Fracture of Engineering Materials & Structures (2023) 

A. Chiocca, M. Sgamma, F. Frendo, F. Bucchi, Rapid and accurate fatigue assessment by an efficient critical plane 290 algorithm: application to a FSAE car rear upright, Procedia Structural Integrity 47 (2023) 749{756. 

E. Ciulli, Friction models for a sustainable design: friction coefficient in lubricated conformal pairs 

Grabovic, E., Artoni, A., Gabiccini, M., Ciulli, E. Exploration of trade-offs between NVH and efficiency in bevel gear design.  Forschung im Ingenieurwesen (2023) 

Abeni, A., Quarto, M. & Ginestra, P.S. Post-processing of powder bed fused stainless steel: micro-machining and micro-electrical discharge machining. J Intell Manuf (2023).   

Ciulli, E. Vastness of Tribology Research Fields and Their Contribution to Sustainable Development. Lubricants 2024, 12, 33. 

Chiocca A., Sgamma M., Frendo F.,  Bucchi F., Marulo M.,  “Fatigue assessment of a FSAE car rear upright by a closed form solution of the critical plane method”, Frattura ed Integrità Strutturale, 18(67), (2023) 153–162. 

Cappellini C., Abeni A., "An analytical micro-milling force model based on the specific cutting pressure-feed dependence, in presence of ploughing and tool run-out effects." Journal of Manufacturing Processes 116 (2024): 224-245. 

Utzeri, M., Lattanzi, A., Kumar, S., Sasso, M. (2024). Dynamic Piezoresistive Behaviour of Composite Materials: Experimental Testing and Analytical Modelling. Mechanics of Composite, Hybrid and Multifunctional Materials, Volume 5. SEM 2023. Conference Proceedings of the Society for Experimental Mechanics Series. 

Seneci, G., Pancera, P.V., Cappellini, C., Abeni, A., Attanasio, A. (2024). An innovative method to model run-out phenomena in micro-milling by using cutting force signal. Materials Research Proceedings 41 (2024) 1867-1876 

Hikaru, A., Binti Juanih, I.F., Quarto, M., Abeni, A., Attanasio, A., D'Urso, G., Ginestra P., Matsumura, T. (2024). Micro-milling and micro-EDM residual stresses evaluation on post-processed 3D printed samples. Materials Research Proceedings 41 (2024) 1860-1866 

Piccininni A., Cusanno A., Ingarao G., Palumbo G., Fratini L., "Investigation of the reshaping process by hydroforming using magnetorheological fluids", Materials Research Proceedings 41 (2024)  2839-2849 

A. Cusanno, P. Guglielmi, D. Sorgente, G. Palumbo, "Numerical/experimental investigation of the effect of the laser treatment on the thickness distribution of a magnesium superplastically formed part", Adv. Manuf. (2024) 

Ciulli E., Grabovic E.; "Pin-on-Disk Wear Investigation on Bronze Coating – Part 1: Definition of the Test Methodology", In: Ciulli, E., Ruggiero, A. (eds) Proceedings of ITS-IFToMM 2024. ITS-IFToMM 2024. Mechanisms and Machine Science (Springer), 160 (2024) 65-76

Grabovic E., Ciulli E., "Pin-on-Disk Wear Investigation on Bronze Coating – Part 2: Analysis of the Experimental Results", In: Ciulli, E., Ruggiero, A. (eds) Proceedings of ITS-IFToMM 2024. ITS-IFToMM 2024. Mechanisms and Machine Science (Springer), 160 (2024)  77-84  

Croccolo D., De Agostinis M., Fini S., Mele M., Nassar S., Olmi G., Scapecchi C., Khan M.Y., Bin Tariq M.H., "Replacing non-renewable lubricants with vegetables oils in threaded joints", Journal of Advanced Joining Processes, 10 (2024) 100234 

A. Chiocca, M. Sgamma, F. Frendo, "How many critical planes? A perspective insight into structural integrity", Procedia Structural Integrity, 58 (2024) 35-41, 7th International Conference on Structural Integrity and Durability (ICSID 2023) 

Solazzi L., Danzi N., "Design and optimisation of a tipping silo semi-trailer by using innovative materials" Composites Part C, 14 (2024) 100469 

Solazzi L., Danzi N., Pasinetti M., "Development and Design of an Innovative and Lightweight Reconnaissance Rover Using Composite Materials" Journal of Multiscale Modelling 15(1) (2024) 2441003 

Candela A., Sandrini G., Gadola M., Chindamo D., Magri P. "Lightweighting in the automotive industry as a measure for energy efficiency: Review of the main materials and methods", Heliyon 10(8) (2024) e29728 

M. Utzeri, M. Sasso, V. S. Deshpande, S. Kumar, "Multiscale Experiments and Predictive Modeling for Failure Mitigation in Additive Manufacturing of Lattices." Adv. Mater. Technol. (2024) 2400457 

Pavlovic A.; Minak G., "Numerical Investigation of Low-Velocity Ice Impact on a Composite Ship Hull Using an FEM/SPH Formulation." Appl. Sci. 14 (2024) 7679

 M. Utzeri, H. Cebeci, S. Kumar, "Autonomous Sensing Architected Materials",  Advanced Functional Materials, 2411975 (2024) 

Grabovic, E., Ciulli, E., Artoni, A., and Gabiccini, M., "Investigation of Thermal Influences on Wear Behavior in Geared Transmissions", SAE Technical Paper 2024-24-0032, (2024)  

E Damiani, M Marsili, M C Righi, “Tuning the adhesion of diamond/copper interfaces through surface chemical modifications and reconstruction”, Carbon 230 (2024) 119555 

Y. Gandhi, A. M. Aragón, J. Norato, G. Minak, "A geometry projection method for the topology optimization of additively manufactured variable-stiffness composite laminates", Computer Methods in Applied Mechanics and Engineering, 435 (2025) 117663 Pasciucco F., Rossi D., Maccaferri E., Pecorini I., Giorgini L., Seggiani M., "Recycling polyamide 6 fishing nets and carbon fibers for the development of novel sustainable composites: Properties and LCA process analysis", Journal of Cleaner Production, 486 (2025) 144634 

Chiocca A., Frendo F., "Fatigue assessment of structural components through the Effective Critical Plane factor", International Journal of Fatigue, 189 (2024) 108565 

G. Sandrini, D. Chindamo, M. Gadola, A. Candela, P. Magri, "Exploring the Impact of Vehicle Lightweighting in Terms of Energy Consumption: Analysis and Simulation on Real Driving Cycle", Energies 17 (2024) 6398 

G. Sandrini, Da. Chindamo, M. Gadola, A. Candela, P. Magri, "Study of different thermal management systems for traction batteries to obtain vehicle lightweighting", Heliyon 11(3) (2025) e42263 

G. Di Egidio, L. Tonelli, A. Morri, I. Boromei, P. Shashkov, C. Martini (UNIBO) “Influence of Anodizing by Electro-Chemical Oxidation on Fatigue and Wear Resistance of the EV31A-T6 Cast Magnesium Alloy” Coatings 2023, 13(1), 62; 

N. Spignoli, G. Minak (UNIBO) “Influence on Fatigue Strength of Post-Process Treatments on Thin-Walled AlSi10Mg Structures Made by Additive Manufacturing” Metals 2023, 13(1), 126; 

L. Girelli, M. Giovagnoli, M. Tocci, A. Fortini, M. Gelfi, M. Merlin, A. Pola (UNIBS) "Impact behavior of gravity cast AlSi10Mg alloy: Effect of hot isostatic pressing and innovative high pressure T6 heat treatment", Frattura ed Integrità Strutturale, 64 (2023) 204-217 NO LINK

Casalino, G., Karamimoghadam, M., Contuzzi, N. (POLIBA), "Metal Wire Additive Manufacturing: A Comparison between Arc Laser and Laser/Arc Heat Sources". Inventions 8 (2023), 52. https://doi.org/10.3390/inventions8020052 

E. Dallari, M. Bononi, A. Pola, M. Tocci, P. Veronesi, R. Giovanardi, Pulsed Current Effect on the Hard Anodizing of an AlSi10Mg Aluminum Alloy Obtained via Additive Manufacturing, Surfaces 2023, 6(1), 97-113.  NO LINK

Tonelli, L.; Liverani, E.; Di Egidio, G.; Fortunato, A.; Morri, A.; Ceschini (UNIBO), L. On the Role of Microstructure and Defects in the Room and High-Temperature Tensile Behavior of the PBF-LB A357 (AlSi7Mg) Alloy in As-Built and Peak-Aged Conditions. Materials 2023, 16, 2721. 

Piccininni A., Lattanzi A., Rossi M., Palumbo G., "Determination of the forming limit curves of locally annealed alluminium blanks", Materials Research Proceedings 28 (2023) 855-865 

Mancini E., Cortis G., Cortese L., Utzeri M., Sasso M., "Simple multiaxial tests to assess dynamic ductility of 17-4PH", Materials Research Proceedings 28, (2023) 1379-1386 

Liu Z, Simonetto E, Ghiotti A, Bruschi S “Compaction behaviour of magneisum alloy-based fibre metal laminates at varying forming parameters” Materials Research Proceedings 28 (2023) 259-266 

Di Egidio, G., Martini, C.,Ceschini, L., Morri, A. (UNIBO), "Influence of Electroless Nickel—DLC (Diamond-like Carbon) Multilayer Coating on the Mechanical Performance of the Heat-Treated AlSi10Mg Alloy Produced by Powder Bed Fusion-Laser Beam". Materials 16 (2023), 3313.  

Liu Z., Simonetto E., Ghiotti A., Bruschi S., “Interply friction behaviour in the temperature-assisted forming of magnesium/glass fibre reinforced thermoplastic polymer laminates” Composites part A: Applied Science and Manufacturing, 173 (2023), 107635 

Piccininni A., Palumbo G., "Numerical modelling of the annealing determined by short-term laser treatment using a physical simulation-based approach" CIRP Journal of Manufacturing Science and Technology, 45 (2023) 210-224 

M. Tocci, A. Pola, M. Modigell, "Rheological Behaviour of Secondary AlSi7Mg Alloy for Semi-Solid Processing", Solid State Phenomena 347 (2023) 107 - 113

A. Mantelli, R. Arcaleni, l. Girelli, L. Tonelli, L. Montesano, A. Pola, "Preliminary Investigation on the Use of Recycled A356 Alloy for Semi-Solid Processing", Solid State Phenomena 347 (2023) 83 - 89

D’Accardi, E.; Palumbo, D.; De Finis, R.; Galietti, U. "Detection and Characterization of Short Fatigue Cracks by Conduction Thermography" Engineering Proceedings Vol.51 Num.23 (2023)  

A. Abeni, P. Ginestra, A. Fiorentino, A. Attanasio, and E. Ceretti, "Modelling of Tube Hydroforming Process: Identification of Best Process Parameters and Comparison Between Different FE Models" International Conference on the Technology of Plasticity (2023), 622-630. 

D’Accardi, E., Palumbo, D., De Finis, R., & Galietti, U. (2023). Detection and Characterization of Short Fatigue Cracks by Conduction Thermography. Engineering Proceedings, 51(1), 23. NO LINK

Cantaboni F., Battini D., Hauber K. Z. , Ginestra P. S., Tocci M., Avanzini A., Ceretti E., Pola A., "Mechanical and microstructural characterization of Ti6Al4V lattice structures with and without solid shell manufactured via electron beam powder bed fusion", The International Journal of Advanced Manufacturing Technology, 2024 

L. Marchini, P. Tonolini, L. Montesano, M. Gelfi, A. Pola, The corrosion resistance of maraging steel 1.2709 produced by L-PBF in contact with molten Al-alloys, Procedia Structural Integrity, Volume 53, 2024, Pages 203-211. 

G. Di Egidio, L. Tonelli, M. Zanni, D. Carosi, A. Morri, L. Ceschini, "Direct artificial aging of the PBF-LB AlSi10Mg alloy designed to enhance the trade-off between strength and residual stress relief", Journal of Alloys and Metallurgical Systems, 5 (2024) 100063 

Sasso, M., Mancini, E., Chiappini, G., Utzeri, M., Amodio, D. (2024). High Strain Rate Tests by a 90 m Long Tension-Torsion Hopkinson Bar. Dynamic Behavior of Materials, Volume 1. SEM 2023. Conference Proceedings of the Society for Experimental Mechanics Series. 

GHINATTI E., BERTOLINI R., GHIOTTI A., BRUSCHI S., "Effect of the hatch spacing in laser powder bed fusion on the AlSi7Mg aluminum alloy cutting forces and surface finish after turning" Materials Research Proceedings 41 (2024) 1907-1915 

E. Ghinatti, R. Bertolini, M. Sorgato, A. Ghiotti, S. Bruschi; "Tool wear and surface finish analysis after drilling Al-SiC metal matrix composite with DLC-coated tools at varying feed", Procedia CIRP 123 (2024) 53–58 

Bertolini R, Stramare A, Sorgato M, Savio E, Ghiotti A, Bruschi S, "On the role of metal surface modification and polymer matrix characteristics when drilling thermoplastic fibre metal laminates.", CIRP Annals – Manufacturing Technology (2024) (ACCEPTED, IN PRESS) 

D’Accardi, E., De Finis, R., Dell’Avvocato, G., Masciopinto, G., Palumbo, D., Galietti, U., "Conduction thermography for non-destructive assessment of fatigue cracks in metallic materials", Infrared Physics & Technology 140 (2024) 105394 

Dell'Avvocato, G., Rashkovets, M., Castellano, A., Palumbo, D., Contuzzi, N., Casalino, G., Galietti, U., "Preliminary procedure for the assessment of probeless friction stir spot welds (P-FSSW) in dissimilar aluminum alloys by long pulsed laser thermography", In Thermosense: Thermal Infrared Applications XLVI (Proc. SPIE 13047), 13047R (2024) 80-90 

A. Boschetto, L. Bottini, D. Pilone, "Metallurgical Defects and Roughness Investigation in the Laser Powder Bed Fusion Multi-Scanning Strategy of AlSi10Mg Parts". Metals  14 (2024) 711 

G. Cortis, M. Piacenti, F. Nalli, L. Cortese, "A direct analytical methodology for the assessment of ductile fracture in metals based on multiaxial tests", FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2024), 1-17 

Cortis G, Piacenti M, Nalli F, Cortese L., "A direct analytical methodology for the assessment of ductile fracture in metals based on multiaxial tests", Fatigue & Fracture of Engineering Materials & Structures (2024) (IN PRESS) 

Sasso M., Mancini E., Chiappini G. et al. "A 90-meter Split Hopkinson Tension–Torsion Bar: Design, Construction and First Tests." J. dynamic behavior mater. (2024) 

G. Pirro, A. Martucci, A. Morri, M. Lombardi,  and L. Ceschini, "A novel solution treatment and aging for powder bed fusion–laser beam Ti–6Al–2Sn–4Zr–6Mo alloy: Microstructural and mechanical characterization", Int. J. Miner. Metall. Mater.,(2024) 

D Carosi, A Morri, L Ceschini, A Ferraiuolo, "A Novel Approach for Evaluating the Influence of Texture Intensities on the First Magnetization Curve and Hysteresis Loss in Fe–Si Alloys", Materials 17 (2024) 3969 

 S. Yaghoubi, A. Piccininni, M. Seidi, P. Guglielmi, "Multi-criteria optimization of the warm hydroforming process of an aluminum component based on the adaptive neuro-fuzzy inference system", Journal of Manufacturing Processes 132 (2024) 75-92 

R. Arcaleni, A. Mantelli, L. Girelli, L. Tonelli, A. Morri, A. Pola, L. Ceschini, "Microstructural characterization of primary and recycled aluminum AlSi7Mg alloy processed by the semi-solid thixocasting method", Materials Characterization 220 (2025) 114657 

A. Cusanno, D. Carty, G. Palumbo, "A novel methodology for affecting the strain paths during hydraulic bulge tests by means of laser heat treatments", European Journal of Mechanics/A, 111 (2025) 105569 

Pirro G., Martucci A., Morri A., Lombardi M., Ceschini L., "A novel solution treatment and aging for powder bed fusion-laser beam Ti-6Al-2Sn-4Zr-6Mo alloy: Microstructural and mechanical characterization", International Journal of Minerals, Metallurgy and Materials, 32 (2025) 414–424 

G. Di Egidio, C. Martini, A. Morri, L. Tonelli, L. Ceschini, M. Tocci, M. Gelfi, A. Pola, A. Martucci, M. Lombardi, "Caratterizzazione di un rivestimento multistrato (Ni-P+DLC) applicato su componenti in lega PBF-LB AlSi10Mg costituiti da geometrie complesse e strutture reticolari", 116 (1) (2025) 8 - 17

M. E. Palmieri, L. Tricarico (POLIBA) "Comparison of Flow Behaviors at High Temperature of Two Press Hardening Boron Steels with Different Hardenability" Metals 2022, 12(11), 1935; 

M.E. Palmieri, P. Posa, A. Angelastro, D. Bassan, M. Colosseo (POLIBA) "Analysis of Transition Zone on a Hot-Stamped Part with Tailored Tool Tempering Approach by Numerical and Physical Simulation"  Steel Research Int. 2200665.  

L. Tricarico, M.E. Palmieri (POLIBA) "Robust Design of Deep Drawing Process through In-Line Feedback Control of the Draw-In" Appl. Sci. 2023, 13(3), 1717; 

M. E. Palmieri, L. Tricarico (POLIBA) "Numerical-experimental study of a tailored press-hardening technology with intermediate pre-cooling to manufacture an automotive component in advanced high strength steel", Materials Research Proceedings, Vol. 25, pp 447-454, 2023 

"Guzmán-Mínguez, J. C.; Granados-Miralles, C.; Kuntschke, P.; de Julián Fernández, C.; Erokhin, S. ; Berkov, D.; Schliesch, T. ; Fernández, J. F. ; Quesada, A., "Remanence Increase in SrFe12O19/Fe Exchange-Decoupled Hard-Soft Composite Magnets Owing to Dipolar Interactions" Nanomaterials 13 (2023) 2097.  

B. Muzzi, M. Albino, M. Petrecca, C. Innocenti, C. de Julián Fernández, G. Bertoni, M. Ricardo Ibarra, M. Christensen, M. Avdeev, C. Marquina, and C. Sangregorio; "Defect-Engineering by Solvent Mediated Mild Oxidation as a Tool to Induce Exchange Bias in Metal Doped Ferrites" Small Methods 2023, 2300647. 

"Effects of the intermediate pre‐cooling parameters on the mechanical properties of a tailored press‐hardened component in advanced high‐strength steel", steel research international, 2300356, (2023) POSSO?

Dell’Avvocato, G., Bison, P., Ferrarini, G., Palmieri, M. E., Palumbo, D., Tricarico, L., & Galietti, U. (2023). Exploring the Correlation between Thermal Diffusivity and Ultimate Tensile Strength in Usibor® 1500 through Laser Thermography. Engineering Proceedings, 51(1), 1. NO LINK

L. Marchini, P. Tonolini, L. Montesano, M. Tocci, A. Pola, M. Gelfi, Cavitation erosion resistance of 1.2709 alloy produced via Laser-Powder Bed Fusion, Procedia Structural Integrity, Volume 53, 2024, Pages 212-220. 

F. Cantaboni, M. Tocci, P. S. Ginestra, A. Pola, E. Ceretti, Production and characterization of lattice samples with solid shell in 17-4 PH stainless steel by Laser Powder Bed Fusion technology, Procedia Structural Integrity, Volume 53, 2024, Pages 65-73. 

Belardini CM, Macoretta G, Monelli BD, Berto F, Tedesco MM, Valentini R. "Modelling of room temperature outgassing and diffusion in a martensitic advanced high-strength steel", Engineering Failure Analysis 162 (2024) 108395 

Di Maro, M., Faga, M.G., Pedraza, R., Malucelli, G.; Bartoli, M., Gomez d'Ayala, G., Duraccio, D. "Effect of Hemp Hurd Biochar and Humic Acid on the Flame Retardant and Mechanical Properties of Ethylene Vinyl Acetate". Polymers 2023, 15(6), 1411 

Laudadio, E., Mohebbi, E., Pavoni, E., Minnelli, C., Sabbatini, S., Stipa, P. "Density functional theory and molecular dynamics studies on electrical, mechanical, and thermal properties of TiO2 nanoparticles interacting with poly lactic-co-glycolic acid".  Colloids and Surfaces A: Physicochemical and Engineering Aspects, Volume 667, 20 June 2023, 131388 

Granata, F., Pirillo, N., Alabastri, A., Schirato, A., et al. "Synthesis of plasmonic gold nanoparticles on soft materials for biomedical applications". Micro and Nano Engineering, 19, 2023, 100207 

L. Luca, M. Degli Esposti, S. Braccini, C. Siracusa, F. Quartinello, G. Guebitz, D. Puppi, D. Morselli, P. Fabbri “A further step in the transition from conventional plasticizers to versatile bioplasticizers obtained by the valorization of levulinic acid and glycerol”, ACS Sustainable Chemistry & Engineering 11 (2023) 9455−9469 

C. Ruini, P. Neri, G. Cavalaglio, V. Coccia, F. Cotana, A. M. Raspolli Galletti, D. Morselli, P. Fabbri, A. M. Ferrari, R. Rosa “Innovative bioplasticizers from residual Cynara cardunculus L. biomass-derived levulinic acid and their environmental impact assessment by LCA methodology” ACS Sustainable Chemistry & Engineering 11 (2023) 12014 − 12026 

D. Rossi, M. Cappello, S. Filippi, P. Cinelli, and M. Seggiani, “Potential of Lauryl Gallate as Stability and Recyclability Improver of Poly (Butylene succinate co adipate)”, J. of Polym. and the Environ., 2023, 

 M. Cappello, D. Rossi, S. Filippi, P. Cinelli, and M. Seggiani, “Wood residue-derived biochar as a low-cost, lubricating filler in poly(butylene succinate-co-adipate) biocomposites”, Materials, vol. 16, no. 570, 2023 

Matarrese, T., Palumbo, D., & Galietti, U. (2023). Comparison in the transient regime of four lock-in thermography algorithms by means of synthetic and experimental data on CFRP. NDT & E International, 139, 102925. 

Christian Müller , Martin H. Müser , Giuseppe Carbone , and Nicola Menga. Significance of Elastic Coupling for Stresses and Leakage in Frictional Contacts. PHYSICAL REVIEW LETTERS 131, 156201 (2023)

Jacopo Agnelli, Claudia Pagano, Irene Fassi, Laura Treccani, Fabio Bignotti, Francesco Baldi. Mechanical behaviour of ductile polymer cellular model structures manufactured by FDM. Mechanics of Materials 190 (2024) 104882 G. Rossignolo, G. Malucelli and A. Lorenzetti. Recycling of polyurethanes: where we are and where we are going. Green Chem., 2024, 26, 1132-1152. 

G. Rossignolo, G. Malucelli and A. Lorenzetti. Recycling of polyurethanes: where we are and where we are going. Green Chem., 2024, 26, 1132-1152. 

I. Bavasso, M. P. Bracciale, G. De Bellis, A. Pantaleoni, J. Tirillò, G. Pastore, S. Gabrielli, F. Sarasini, "Recycling of a commercial biodegradable polymer blend: Influence of reprocessing cycles on rheological and thermo-mechanical properties", Polymer Testing 134 (2024) 108418 

A. Pantaleoni, F. Sarasini, P. Russo, J. Passaro, L. Giorgini, I. Bavasso, M. L. Santarelli, E. Petrucci, F. Valentini, M. P. Bracciale, A. Marrocchi, "Facile and Bioinspired Approach from Gallic Acid for the Synthesis of Biobased Flame Retardant Coatings of Basalt Fibers", ACS Omega, 2024, 10.1021/acsomega.3c10129 

T. Dubaj, S. Vecchio Ciprioti, J. Tirillò, F. Sarasini, "Thermal stability of binary and ternary biodegradable polymer blends assessed by isoconversional kinetic analysis", Thermochimica Acta 736 (2024) 179761 

E. Togliatti, L. Lenzi, M. Degli Esposti, M. Castellano, D. Milanese, C. Sciancalepore, D. Morselli*, P. Fabbri “Enhancing melt-processing and 3D printing suitability of polyhydroxybutyrate through compounding with a bioplasticizer derived from the valorization of levulinic acid and glycerol” Additive Manufacturing (2024) 104290 (ACCEPTED, IN PRESS) 

G. Malucelli, "Nanostructured Flame-Retardant Layer-by-Layer Architectures for Cotton Fabrics: The Current State of the Art and Perspectives". Nanomaterials 14 (2024) 858 

Mandriota C., Menga N., & Carbone,G., "Adhesive contact mechanics of viscoelastic materials", International Journal of Solids and Structures, 290 (2024) 112685

Mandriota C, Menga N, Carbone G, "Enhancement of adhesion strength in viscoelastic unsteady contacts", Journal of the Mechanics and Physics of Solids 192 (2024) 105826  

E. Mohebbi, C. Minnelli, E. Pavoni, L.Sisti, E. Laudadio, P, Stipa, “Layered Double Hydroxides as Systems for Capturing Small-Molecule Air Pollutants: A Density Functional Theory Study”, Molecules, 29 (2024) 4996 

E. Maccaferri, L. Mazzocchetti, T. Benelli, J. Ortolani, T. Maria Brugo, A. Zucchelli, L. Giorgini (UNIBO) “Is Graphene Always Effective in Reinforcing Composites? The Case of Highly Graphene-Modified Thermoplastic Nanofibers and Their Unfortunate Application in CFRP Laminates” Polymers 2022, 14(24), 5565; 

M.P. Falaschetti, F. Rondina, E. Maccaferri, L. Mazzocchetti, L. Donati, A. Zucchelli, L. Giorgini (UNIBO) “Improving the crashworthiness of CFRP structures by rubbery nanofibrous interlayers” Composite Structures 2023, 311, 116845; 

Spurio, E.; Pelli Cresi, J.S.; Ammirati, G.; Pelatti, S.; Paladini, A.; D’Addato, S.; Turchini, S.; O’Keeffe, P.; Catone, D.; Luches, P. Injecting electrons into CeO2 via photoexcitation of embedded Au nanoparticles, ACS Photonics 2023; 10(5):1566–1574. 

Sergi, C., Tirillò, J., Iacovacci, C., Sarasini, F. "Influence of reprocessing cycles on the morphological, thermal and mechanical properties of flax/basalt hybrid polypropylene composites". Sustainable Materials and Technologies, 2023. 

Carraro PA, Simonetto M, Quaresimin M, Fatigue damage evolution in glass/epoxy cross-ply laminates under spectrum loadings, Composites: Part A 173 (2023) 107680 

Pavlović, A.; Minak, G. FEM-SPH Numerical Simulation of Impact Loading on Floating Laminates. J. Mar. Sci. Eng. 2023, 11, 1590.  

F. Angeletti, D. Tortorici, S. Laurenzi, P. Gasbarri, Vibration Control of Innovative Lightweight Thermoplastic Composite Material via Smart Actuators for Aerospace Applications, Applied Sciences 13 (17), 9715 

F. Angeletti, P. Gasbarri, M. Panella, A. Rosato, Multi-Damage Detection in Composite Space Structures via Deep Learning, Sensors 23 (17), 7515 

Tortorici D., Sabatini M., Laurenzi S., Numerical simulations and experimental results of the deployment of thin-walled bistable composite booms, Composite Structures, 327, 117669, 2024 

D. Marchese, C. Giosuè, A. Staffolani, M. Conti, S. Orcioni, F Soavi, M. Cavalletti, P. Stipa, "An Overview of the Sustainable Recycling Processes Used for Lithium-Ion Batteries", Batteries  10(1), 2024, 27 

E. Laudadio, E. Mohebbi, E. Pavoni, C. Minnelli, S. Sabbatini, P. Stipa, "Density functional theory and molecular dynamics studies on electrical, mechanical, and thermal properties of TiO2nanoparticles interacting with poly lactic-co-glycolic acid", Colloids and Surfaces A: Physicochemical and Engineering Aspects  667, 131388, 2023. 

Lamon F., Maragoni L., Carraro P.A., Quaresimin M., "Influence of the mesostructure on the fatigue behaviour of textile composites", Composites: Part A 181 (2024) 108115 

N. Giani, E. Maccaferri, T. Benelli, M. Bovo, D. Torreggiani, E.G. Campari, P. Tassinari, L. Giorgini, L. Mazzocchetti, "Valorization of Agro-Wastes as Fillers in PLA-Based Biocomposites for Increasing Sustainability in Fused Deposition Modeling Additive Manufacturing", Materials (Basel), 17 (2024) 1421 

M. Elaheh, E. Pavoni, C. Minnelli, R. Galeazzi, G. Mobbili, S. Sabbatini, P. Stipa, M. M. Seyyed Fakhrabadi, E. Laudadio, "Adsorption of Polylactic-co-Glycolic Acid on Zinc Oxide Systems: A Computational Approach to Describe Surface Phenomena" Nanomaterials 14, 8 (2024) 687 

A. Papavassiliou, A. Pavlovic, G. Minak, "Crashworthiness investigation on a Carbon Fiber Reinforced Plastic solar vehicle", Composite Structures (2024) 118147 

C. Sergi, L. Botta, J. Tirillò, F. Sarasini, "Basalt/polypropylene composites: The effects of mechanical reprocessing on their morphological, thermal, rheological and mechanical behavior", Materials Today Sustainability 27 (2024) 100843 

Dell'Avvocato, G., Rashkovets, M., Castellano, A., Palumbo, D., Contuzzi, N., Casalino, G., Galietti, U., "Preliminary procedure for the assessment of probeless friction stir spot welds (P-FSSW) in dissimilar aluminum alloys by long pulsed laser thermography", In Thermosense: Thermal Infrared Applications XLVI (Proc. SPIE 13047), 13047R (2024) 80-90 

Mongioì, F., Selleri, G., Brugo, T. M., Maccaferri, E., Fabiani, D., Zucchelli, A., "Multifunctional composite material based on piezoelectric nanofibers and Cu-CFRP electrodes for sensing applications", Composite Structures 337 (2024) 118076 

Mohebbi E., Pavoni E., Minnelli C., Galeazzi R., Mobbili G., Sabbatini S., Stipa P., Fakhrabadi M.M.S., Laudadio E., "Adsorption of Polylactic-co-Glycolic Acid on Zinc Oxide Systems: A Computational Approach to Describe Surface Phenomena", Nanomaterials 14 (2024) 687 

Amadori T., Maccaferri E., Ortolani J., Mazzocchetti L., Benelli T., Minosi S., Corvaglia S., Giorgini L., "Investigation and Optimization of CFRP Recycling by Pyrogasification Process", Macromolecular Symposia, 2400020 (2024) 

L. Giorgini, P. Natali, L. Sisti, M. Vannini, E. Maccaferri, T. Benelli, L. Mazzocchetti, "Evaluation of the Effect of Recycling of Carbon Fibers for Polypropylene Reinforcement", Macromolecular Symposia, 2400013 (2024) 

P. Natali, L. Mazzocchetti, D. Bertoldo, E. G. Campari, T. Benelli, E. Maccaferri, N. Giani, L. Giorgini, "Study of the Behavior of 3D Printed Thermoplastic Elastomers Structures Aimed at Emulating Traditional Polyurethane Foams", Macromolecular Symposia, 2400027 (2024) 

E. Maccaferri, J.Ortolani, L. Mazzocchetti, T. Benelli, T. M. Brugo, A. Zucchelli, L. Giorgini, "Toughened CFRPs via PEO Nanofibers: Effect of Water Ageing on Delamination", Macromolecular Symposia, 2400253 (2024) 

Carraro PA, Pontefisso A, Panozzo F, Quaresimin M, Zappalorto M. Health monitoring of bonded joints through electrical measurements. Structural Health Monitoring. 2024;0(0) 

P. Cuccarollo, A. Pontefisso, P. A. Carraro, M. Quaresimin, "Characterization and modelling of the microstructural and mechanical properties of additively manufactured continuous fiber polymer composites", Composites Science and Technology, 260 (2025) 110986  

Mohebbi E., Minnelli C., Pavoni E., Sisti L., Laudadio E., Stipa P., "Layered Double Hydroxides as Systems for Capturing Small-Molecule Air Pollutants: A Density Functional Theory Study", Molecules 29 (2024) 4996 

Mongioì F., Selleri G., Maccaferri E., Fabiani D., Zucchelli A., Brugo T.M., "CFRP laminate with autonomous sensing and enhanced impact resistanceby P(VDF-TrFE) nanofibers interleaving", Composites Part B, 293 (2025) 112143 

Pantaleoni A., Marrocchi A., Russo P., Malucelli G., Altamura D., Nardelli F., Pizzanelli S., Freni A., Giannini C., Santarelli M.L., Bavasso I., Bracciale M.P., Sarasini F. "Advanced flame-retardant biocomposites: Polylactic acid reinforced with green gallic acid‑iron‑phosphorus coated flax fibers", International Journal of Biological Macromolecules, 300 (2025), 140215 

G. Palumbo, Optimization of the Sheet Hydroforming process parameters to improve the quality of reshaped EoL components, The 20th International Conference on Sheet Metal (SHEMET 2023)

 Minak, Structural Design of Solar Powered Vehicles, E-tech Europe 2023

Righi, Tribology International Conference 2023 (Lisbon, 26-28 April 2023)

Minak, Testimonial di una cooperazione di successo in automotive design, Incontro degli addetti scientifici delle ambasciate on line presso MAECI

Minak, Geometry projection method for designing and manufacturing variable-stiffness composite laminate, YSESM 2023

Pietro Cuccarollo, Interlaminar crack propagation in continuous fibre 3D printed laminates, ICFC9 - the ninth International Conference on Fatigue of Composites  - Vicenza 21-23 June 2023

Eugeniu Grabovic, Numerical Analysis of Wear on Hypoid Gears: Influence of Lubrication properties and Wear Partition Factor, ECOTRIB 2023 – 8th European Conference on Tribology

Enrico Ciulli, Friction Models for a Sustainable Design: Friction Coefficient in Lubricated Conformal Pairs, 2nd IFToMM for Sustainable Development Goals Workshop - I4SDG 2023 - Bilbao, Spain June 22-23, 2023

Minak, Modello numerico ibrido FEM-SPH per il carico di impatto su laminati galleggianti, Giornata in ricordo di Ettore Funaioli

Luca Ciacci, Critical resources in the automotive sector A life cycle perspective on supply risk, material flows and stocks, International Summer School Industrial Engineering for Advanced Automotive

Yogesh Gandhi, Geometry projection method for designing and manufacturing multilayered composite laminate, AIAS National Conference 6-8/09/2023

E.Grabovic, E. Ciulli, A. Artoni, M. Gabiccini, F. Di Puccio, L. Mattei, Numerical analysis of wear on hypoid gears: influence of lubrication properties and wear partition factor, ECOTRIB2023

Andrea Abeni, An Innovative Method to Model Run-out Phenomena in Micro-milling by using Cutting Force Signal, 27th International ESAFORM Conference on Material Forming (ESAFORM 2024) 

Antonio Piccininni, Investigation of the reshaping process by hydroforming using magnetorheological fluids, 27th International ESAFORM Conference on Material Forming (ESAFORM 2024)  

International Summer School Industrial Engineering for Advanced Automotive 

Angela Cusanno, Laser Heat Treatment prior to superplastic forming for tailoring the thickness distribution of a magnesium AZ31 component, 15th European Conference on Superplastic Forming (EuroSPF2024) 

Emanuele Fulco, Numerical study of the Reshaping process of End-of-Life components by gas forming at elevated temperatures, The 15th European Conference on Superplastic Forming (EuroSPF2024) 

Giuseppe Macoretta, Cyclic elastic loading behavior in pre-strained lattice structures, Cyclic elastic loading behavior in pre-strained lattice structures 

Mattia Mele, replacing non-renewable lubricants with vegetables oils in threaded joints, Convegno AIAS, Napoli, September 4-6 2024, Napoli, Italy 

Michela Dell'Anna, Cellulose Recovery from Tunicates: a Circular Economy Approach for Aquaculture-Waste Management, 2024 IEEE INTERNATIONAL WORKSHOP ON Metrology for the Sea 

Sandrini Giulia, Primary and Secondary Vehicle Lightweighting Achieved by Acting on the Battery Thermal Management System, 16th International Symposium on Advanced Vehicle Control (AVEC’ 24); September 2-6, 2024; Milan (Italy) 

Tocci, Trattamento termico innovativo in getti pressocolati in lega AlSI10Mg, Fonderia e Pressofusione

Convegno Assofond

Surface engineering of additively-manufactured light alloys: microstructure and tribological behaviour, 36324-1 EMMA-MCL Open Seminar

Centro Nazionale Mobilità Sostenibile: Spoke 11 - Materiali innovativi e alleggerimento, Giornata di Studio AIM - I laminati di Alluminio

Lucio Maragoni, Analysis of crack-induced delamination in composite laminates under tensile fatigue loadings, ICFC9 - the ninth International Conference on Fatigue of Composites  - Vicenza 21-23 June 2024

Lavinia Tonelli, Assessment of low and high cycle fatigue behaviour of the PBF-LB AlSi7Mg alloy in the as-built and heat-treated conditions: influence of defects and microstructural features, Euromat 2023

Pietro Tonolini, the corrosion resistance of maraging steel 1.2709 produced by L-PBF in contact with molten alalloy, ESIAM 2023 

Anna Mantelli, Preliminary investigation on the use of recycled A356 alloy for semi solid processing, S2P 2023 

Marialaura Tocci, Rheological behaviour of secondary AlSi7Mg alloy for semi-solid processing, S2P 2023

Ester D'Accardi, Diagnostica e caratterizzazione di cricche da fatica tramite conduction thermography, AIAS2023 Conference 

Aldo Attanasio, Modelling of Tube Hydroforming process: identification of best process parameters and comparison between different FE models, ICTP2023 Conference 

Ester D'Accardi, Detection and Characterization of Short Fatigue Cracks by Conduction Thermography, AITA2023 Conference 

Comparison of mechanical performance and cracking mechanisms between primary and secondary (recycled) HPDC AlSi10Mg aluminum alloys, 5th International Conference on Thermal Process Modeling and Simulation (TPMS-5) - held in Lecce (taly) on 17-19 April 2024.

Pirro, A novel STA heat treatment for Powder Bed Fusion - Laser Beam Ti-6Al-2Sn-4Zr-6Mo alloy, 4th symposium on materials and additive manufacturing – additive 2024 

Edoardo Ghinatti, Effect of the hatch spacing in laser powder bed fusion on the AlSi7Mg aluminum alloy cutting forces and surface finish after turning , 27th International ESAFORM Conference on Material Forming (ESAFORM 2024)  

Edoardo Ghinatti, Tool wear and surface finish analysis after drilling Al-SiC metal matrix composite with DLC-coated tools at varying feed, 7th  CIRP conference on surface integrity - CSI 

Giuseppe Dell'Avvocato, SPIE - THERMOSENSE 2024

Tiziana Matarrese, SPIE - THERMOSENSE 2024 

Ester D'Accardi, Induction thermography for surface crack detection during motion tests, 3rd International Symposium on Industrial Engineering and Automation (ISIEA 2024) 

Beatrice Abrami, Comportamento a corrosione e a erosione per cavitazione della lega AlSi10Mg prodotta tramite manifattura additiva: effetto dei rivestimenti di Ni-P e Ni-P+DLC, 40° Convegno Nazionale AIM, 11-13 Settembre 2024, Napoli 

Elena Mingotti, Ottimizzazione del trattamento termico di un getto strutturale prodotto in lega AlSi10MnMg da riciclo mediante pressocolata, 40° Convegno Nazionale AIM, 11-13 Settembre 2024, Napoli 

Luca Marchini, Corrosione da metallo liquido di acciai per stampi immersi in leghe di alluminio per pressocolata a diverso contenuto in lega di Si, 40° Convegno Nazionale AIM, 11-13 Settembre 2024, Napoli 

Lavinia Tonelli, Effect of different process conditions and post-process treatments on residual stress and fatigue behavior of the AlSi10Mg PBF-LB alloy, European Conference on Fracture 2024 - ECF24 August 26 - 30, 2024. Zagreb, Croatia 

Caratterizzazione di un rivestimento multistrato (Ni-P+DLC) applicato su componenti in lega PBF-LB AlSi10Mg costituiti da geometrie complesse e strutture reticolari, 40th National Conference of the Italian Metallurgy Association (AIM) September 11-13, 2024, Naples, Italy 

Ester D'Accardi, Increasing Scanning Speed During Induction Thermography Tests: Simulations and Experimental Tests to Investigate Crack Detectability, Convegno QIRT, Zagabria, July 1-5 2024, Croazia 

Giuseppe Dell'Avvocato, Towards Comprehensive Quantification: Preliminary Laser Thermography Procedure in Probeless Friction Stir Spot (P-FSSW) Aluminium Welding, Convegno QIRT, Zagabria, July 1-5 2024, Croazia 

Giuseppe Dell'Avvocato, excploring laser thermography for strength evaluation of probeless fssw dissimilar alluminium welding: a preliminary study, Convegno AIAS, Napoli, September 4-6 2024, Napoli, Italy 

Ester D'Accardi, INDUCTION THERMOGRAPHY COME CONTROLLO NON DISTRUTTIVO PER LA CARATTERIZZAZIONE DELLE CRICCHE AD ELEVATE VELOCITÀ: RISULTATI SPERIMENTALI E CURVE PROBABILITY OF DETECTION, Convegno AIAS, Napoli, September 4-6 2024, Napoli, Italy 

Giuseppe Dell'Avvocato, Advances in Non-Destructive Analysis of Biodegradable Mg AZ31 Magnesium Alloys through Pulsed Laser Thermography, Convegno QIRT, Zagabria, July 1-5 2024, Croazia 

F. Albertini, "Magnetic shape memory Heuslers: microstructure-related effects on the martensitic transformation", Symposium  "Green Magnets for Efficient Energy Conversion" Spring Meeting 2023 DPG, Condensed Matter Section (Dresden, March 26-31, 2023) 

F. Albertini, "Tailoring of local magnetic properties for new generation of high energy rare earth based permanent magnets" , CNR-Jozef Stefan Institute - Networking Event (online)

F. Albertini, "Magnetic shape memory Heuslers: microstructure related effects on the martensitic transformastion"(invited talk), DPG Spring Meeting of the Condensed Matter Section - Symposium Green Magnets for Efficient Energy Conversion (Dresden 26-31 March 2023)

Cesar de Julian Fernandez, Kickoff meeting del progetto “Knowledge Integration for Neighborhoods in Energy Transition led by Inclusive Communities” (KINETICS), presso CNR-IMEM (Parma), “Materiali Magnetici per la Transizione Energetica Green” 

Francesco Cantaboni, Production and characterization of lattice samples with solid shell in 17-4 PH stainless steel by Laser Powder Bed Fusion technology, ESIAM 2023 

Luca Marchini, Cavitation erosion resistance of 1,2709 Maraging steel manufactured via laser powder bed fusion, ESIAM 2023 

Carlo Maria Belardini et al., A study of the effects of hydrogen on martensitic advanced high-strength steels, 5th International Conference on Structural Integrity (ICSI2023)   https://www.icsi.pt?

Franca Albertini, I magneti permanenti: presente e futuro, AIM- Innovazione dei materiali per la mobilità elettrica 

César de Julian Fernandez, I materiali magnetici come materiali critici, la Notte dei Ricercatori 2023 (IMEM-CNR) 

César de Julian Fernandez, I materiali magnetici come materiali critici, Porte Aperte al CNR (Area della Ricerca di Bo) 

César de Julian Fernandez, I materiali magnetici come materiali critici, Laboratorio di Sostenibilità (IMEM-CNR) 

César de Julian Fernandez, I materiali magnetici come materiali critici, REPM2023 Conference 

Riccardo Cabassi, Steps towards the hardening of Cobalt ferrite nanopowders, AITA2023 Conference 

Giuseppe Dell'Avvocato, Exploring the Correlation between Thermal Diffusivity and Ultimate Tensile Strength in Usibor® 1500  through LaserThermography, AITA2023 Conference 

Carlo Maria Belardini, An investigation on hydrogen embrittling mechanisms in martensitic advanced high-strength steels, European Conference on Fracture 2024 - ECF24, August 26 - 30, 2024. Zagreb, Croatia 

Bernardo Disma Monelli, Hydrogen-assisted degradation of 3rd generation of martensitic advanced high-strength steels, European Corrosion Congress EUROCOR 2024, 1-5 September 2024, Paris, France 

Bernardo Disma Monelli, Studio numerico e sperimentale della diffusione e del degasaggio dell’idrogeno   in acciai martensitici altoresistenziali, 40th National Conference of the Italian Metallurgy Association (AIM) September 11-13, 2024, Naples, Italy 

Sarasini, Le attività di ricerca dello Spoke 11 - Materiali Innovativi e Alleggerimento finanziate nell’ambito del Centro Nazionale per la Mobilità Sostenibile (MOST), Final Event LIFEBIOCOMPO project

Sarasini, Le attività di ricerca dello Spoke 11 - Materiali Innovativi e Alleggerimento finanziate nell’ambito del Centro Nazionale per la Mobilità Sostenibile (MOST), on Fatigue of Composites

Claudia Sergi, Ti6Al4V manufactured by coupling fused deposition modeling (FDM) and sintering: Mechanical propertiesoptimation, XVII Convegno AIMAT (Associazione Italiana di Ingegneria dei Materiali) - 28maggio-1giugno 2023, Catania

Alessia Pantaleoni, Facile and bioinspired development of a novel bio-based coating from gallic acid of

NATURAL FIBERS FOR COMPOSITE APPLICATIONS6th International Conference on Natural Fibers - Nature Inspired Sustainable Solutions. Funchal, Madeira (Portugal) - 19-21 June 2023

Claudia Sergi, TGA, DSC e DMA: l'analisi termica al servizio dell'ottimizzazione di materiali e processi produttivi ecosostenibili, L'Analisi Termica e la Reologia per lo Studio dei Polimeri e dei Compositi - EURO HOTEL RESIDENCE Via Monza, 27 - 20863 CONCOREZZO (MB)

Francesco Baldi, Fracture characterization of ductile polymer cellular model structures manufactured by FDM, 9th International Conference on Fracture of Polymers, Composites and Adhesives

Damiano Rossi (Department of Civil and Industrial Engineering, University of Pisa), Composite materials for automotive applications based on recycled fishing nets and biochar, Bioeconomy-Day, Università di Pisa (DICI) 

Damiano Rossi (Department of Civil and Industrial Engineering, University of Pisa), Composite materials for automotive applications based on recycled fishing nets and biochar, XIV Convegno INSTM sulla Scienza e Tecnologia dei Materiali 

Luigi Gamberini, Miscele polimeriche di acido polilattico con materiali termoindurenti biobased, chimicamente riciclabili e self-healing, Workshop Plastiche & Ambiente 

Luigi Gamberini, Blends of polylactic acid with biobased, chemically recyclable, and self-healable thermoset, XIV Convegno INSTM sulla Scienza e Tecnologia dei Materiali 

Luigi Gamberini, Polymer mixtures of polylactic acid with biobased, chemically recyclable, and self-healing thermosetting materials, Symposium for Young Chemists: Innovation and Sustainability (SYNC 2024) 

Alessia Pantaleoni, Sustainable green coating for natural fiber: a flame retardant approach to PLA-based composites, Symposium for Young Chemists: Innovation and Sustainability (SYNC 2024) 

Paola Fabbri, The "full-bio" strategy: The relevance of functional bio-based additives for the formulation of innovative plastics, 85TH PRAGUE MEETING ON MACROMOLECULES – POLYMERS FOR SUSTAINABLE FUTURE 

Multiscale Characterization and Imaging of nano/bio-materials by X-ray microdiffraction and microscopy, 3° Simposio Futuro IN Area 

21st European Conference on Composite Materials (ECCM21) 

Davide Morselli, Levulinic Acid/Glycerol-Based Bioplasticizer for Enhancing Properties and Processability of Polyhydroxyalkanoates (PHAs), 5th International Conference on Bio-based Polymers and Composites (BiPoCo) 

Irene Bavasso, trade-off between performance and processability of PLA/PBAT/PHBV-FLAXcomposites: effect of flax fibers surface modification, 21st European Conference on Composite Materials (ECCM21)

Alessia Pantaleoni, Sustainable green coating for natural fibers: a flame retardant approach for pla-based composites, 21st European Conference on Composite Materials (ECCM21)

Davide Palumbo, SVILUPPO DI UNA PROCEDURA DI POST-PROCESSING PER LA VALUTAZIONE DELL’ESTENSIONE E DELLA PROFONDITÀ DELL’AREA DANNEGGIATA IN PROVINI IBRIDI CON FIBRE NATURALI MEDIANTE TERMOGRAFIA PULSATA, Convegno AIAS, Napoli, September 4-6 2024, Napoli, Italy 

Fabrizio Sarasini, Assessment of the impact behavior of basalt/epoxy laminates and their end-of-life scenario as a function of impactor mass, temperature and pyro-gasification parameters, American Society for Composites 39th Annual Technical Conference, October 21-23, 2024, San Diego (USA)

Sara Taherinezhad Tayebi, Co-processing Wind Turbine Blades to Avoid Microplastics Accumulation in Marine Ecosystem, Recent Trends in Microplastic Research; May 22-26, 2023; Jena (Germany) 

Emanuele Maccaferri, Toughened CFRPs via PEO nanofibers: effect of water ageing on delamination, TOP Conference 2023

Tommaso Amadori, Investigation and optimisation of CFRP recycling by pyrogasification process, TOP Conference 2023

Paolo Andrea Carraro, Damage evolution in glass/epoxy laminates subjected to spectrum loadings, ICFC9 - the ninth International Conference on Fatigue of Composites  - Vicenza 21-23 June 2023 

Elisa Tortorelli, Refined structural theories for dynamic analysis of composite structures subjected to random excitation, ICFC9 - the ninth International Conference on Fatigue of Composites  - Vicenza 21-23 June 2023

Federico Lamon, Fatigue damage evolution in woven laminates with different meso-structure, ICFC9 - the ninth International Conference on Fatigue of Composites  - Vicenza 21-23 June 2023

Minak, Mobilità sostenibile e materiali innovativi in campo aeronautico, Ordine degli ingegneri della provincia di Forlì-Cesena

Quaresimin/Merulla/Avataneo, «Materiali e metodologie innovative per la progettazione sostenibile in automotive» (workshop nell'ambito del forum),1^ Forum Sostenibilità Confartigianato 27- 28 giugno 2023, Roma)

Minak, SPH-FEM simulation of lightweight structure under ice impact, AIAS National Conference 6-8/09/2023

Federico Lamon, Previsione della perdita di rigidezza a fatica in compositi bundle-based per applicazioni eoliche, AIAS National Conference 6-8/09/2023

Erasmo Carrera, Refined structural theroies for dynamic and fatigue analyses of structure subjected to random excitations, AIDAA XXVII International Congress

Federica Angeletti, Data-driven deep neural network for structural damage detection in composite

SOLAR ARRAYS ON FLEXIBLE SPACECRAFTItalian Association of Aeronautics and Astronautics, XXVII International Congress4-7 September 2023, Padua, Italy

Federica Angeletti, Active vibration control of smart lightweight composite structures for a small flexible spacecraft, 74th International Astronautical Congress 2023, 2 - 6 OCTOBER 2023, BAKU, AZERBAIJAN

Paola Luches, Ultrafast dynamics of photoexcited states in cerium oxide, CMD 30 Fismat 2023 

Stefania Benedetti, role of Cu dopant in H2 dissociation on Cu:CeO2 surface, ECOSS 36 2003 

Eleonora Spurio, Ultrafast dynamics of photoexcited states in cerium oxide, SILS Conference 2023 

Prof. Marino Quaresimin,  Prof. Michele Zappalorto ,  Prof. Paolo Andrea Carraro,  Prof. Lucio Maragoni (University of Padova), Prof. Ramesh Talreja (Texas A&M University), Dr. Soraia Pimenta (Imperial College London), Prof. Alberto Barroso (University of Seville), Dr. Paolo Fornasiero (Head of Industrial Technology Quality, AIRBUS), Dr. Yongxin Huang (Chief Engineer Blade Structure Design, Siemens Gamesa), 4th International Summer School on Fatigue and Damage Mechanics of Composite Materials 

Elisa Tortorelli, 2D higher-order theories for progressive damage model of composite structures based on hahin and puck failure criteria , 4th Aerospace PhD-Days 2024 

Federica Angeletti, An experimental-data-driven deep learningstrategy for Structural Health Monitoring ofa plate in acoustic fields, 30th AIAA/CEAS Aeroacoustics Conference 

SPIE - THERMOSENSE 2024 

Claudia Sergi, effects of temperature and electro spun veils on the low velocity impact response of basalt/epoxy composites tested with different impactor masses and impact energies, 21st European Conference on Composite Materials (ECCM21) 

Emanuele Maccaferri, rubbery nanofibers via blend and emulsion electrospinning for structural modification, 21st European Conference on Composite Materials (ECCM21)

Emanuele Maccaferri, electrospun interleaves made of thermoplastic-thermosetting resin for impoving delamination re-sistance and delivering potential self-healing capa-bility in composite laminates, XXV Convegno Nazionale AIM - Associazione Italiana di Scienza e Tecnologia delle Macromolecole  

Marino Quaresimin, integrated framework for manufacturing, design and monitoring of composite bonded joints: an overview of the results of idea project (MOST)

Federico Lamon, influenza della mesostruttura sul comportamento a fatica di compositi tessuti, Convegno AIAS, Napoli, September 4-6 2024, Napoli, Italy 

Sara Taherinezhad Tayebi, PHYSICAL, MORPHOLOGICAL, AND MECHANICAL CHARACTERIZATION OF RECYCLED HYBRID NON-WOVEN MATS AS A CONTINUOUS FIBROUS REINFORCEMENT FOR NOVEL ECOSUSTAINABLE LIGHT-WEIGHT PMMA THERMOPLASTIC , XIV Convegno INSTM sulla Scienza e Tecnologia dei Materiali, Cagliari, 9-12 giugno 2024

Minak, Evento di presentazione del Video SASOL a Maranello

Maria Cinefra, Detection of delaminations in damaged composite plates via local damage resonance approach, 34th Congress of the International Council of the Aeronautical Sciences (ICAS2024) 

Pola, I progetti di ricerca in ambito sostenibilità dell'Università degli Studi di Brescia. Materiali e Alleggerimento, Futura expo

Gadola/Pola/Baldi, Progettualità nell'ambito del Centro Nazionale Mobilità Sostenibile, Spoke 11 - Materiali per l'Alleggerimento, CLM (Cluster Lombardo della Mobilità) Tavolo alleggerimenti

Ceschini, "Materiali innovativi e alleggerimento per una mobilità sostenibile”  during the "FORUM ITALO – TEDESCO: 2035 E LA FILIERA AUTOMOTIVE", MECSPE 2023 - La fiera internazionale di riferimento per l'industria manifatturiera 29-31/03/2023 

"Materiali innovativi e alleggerimento per una mobilità sostenibile”  during the "FORUM ITALO – TEDESCO: 2035 E LA FILIERA AUTOMOTIVE", MECSPE 2023 - La fiera internazionale di riferimento per l'industria manifatturiera 

Pola/Baldi, Progettualità nell'ambito del Centro Nazionale Mobilità Sostenibile, Spoke 11 - Materiali per l'Alleggerimento, CLM (Cluster Lombardo Mobilità) Tavolo Materiali - Gruppo Tematico “Materiali-Sport-alleggerimento”

Lorella Ceschini, Centro Nazionale Mobilità Sostenibile: Spoke 11 – materiali innovativi e alleggerimento, Workshop "Innovazione nei materiali per la mobilità elettrica" held at BIREX Competence Center - Bologna

A. Pola at al., Progetto PNRR - Centro nazionale per la mobilità sostenibile MOST - Spoke 11 Materialiinnovativi e alleggerimento, FUTURA EXPO 2023 - Economia per l'ambiente (EXPO italiana sulla sostenibilità) 8-10/10/2023: stand exhibition 

Presentazione del progetto Spoke 11 Materiali innovativi e alleggerimento, FUTURA EXPO 2023 - Economia per l'ambiente (EXPO italiana sulla sostenibilità) 8-10/10/2023 

Gianfranco Palumbo, Materiali innovativi e alleggerimento per la mobilità sostenibile, MECSPE BARI 2023 - Tecnologie per l'innovazione - 23-25/11/2023 

Angela Cusanno, Utilizzo di mezzi flessibili per la produzione di componenti leggeri e sostenibili, MECSPE BARI 2023 - Tecnologie per l'innovazione - 23-25/11/2023 

Ester D'Accardi, I metodi termici nella Meccanica Sperimentale al servizio della mobilità sostenibile, MECSPE BARI 2023 - Tecnologie per l'innovazione - 23-25/11/2023 

Maria Laura Gatto, Metalli ferrosi: dagli acciai per l’uso di idrogeno, nuove soluzioni ingegneristiche per dispositivi antiintrusione, ghise innovative per sistemi frenanti ad alta efficienza, e materiali per l’alimentazione elettrica, MECSPE BARI 2023 - Tecnologie per l'innovazione - 23-25/11/2023 

Cluster Lombardo della Mobilità (CLM), WG Tavolo alleggerimenti 

SPOKE 11: Workshop RTDA & SPOKE Meeting (25-26/01/2024)

Overview of Spoke 11 activities within 2 seminars for the 2nd level Master Degree on Sustainable and Integrated Mobility in Urban Regions (SIMUR), University of Bologna 

Annalisa Pola/Jacopo Agnelli, Progettualità nell'ambito del Centro nazionale mobilità sostenibile, spoke 11 - materiali per alleggerimento, Cluster Lombardo della Mobilità (CLM), WG Tavolo alleggerimenti 

GIORNO 25 gennaio: D’Accardi; Maccaferri; Lamon; Angeletti; Morselli; Sergi; Nardelli; Rossi; Gatto; Macoretta; Takhsha Ghahfarokhi; Utzeri; Tonelli; Girelli; Cusano; Abeni;     GIORNO 26 gennaio: Mele; UTZERI; D’Accardi; Grabovic; Frendo; Ceschini; Cabibbo; Sarasini; Quaresimin, Simposio RTDA MOST, SPOKE 11: Workshop RTDA & SPOKE Meeting (25-26/01/2024)

Metallic Materials for Lightweighting, Surface Engineering of Metals & Alloys, Overview of Spoke 11 activities within 2 seminars for the 2nd level Master Degree on Sustainable and Integrated Mobility in Urban Regions (SIMUR), University of Bologna

L. Ceschini, L. Tonelli, A. Pola, M. Cabibbo, R. Valentini, P. Ferro, Leghe ad alte prestazioni - Le opportunità per il settore automotive all’interno del PNRR - at Fiera di Bologna in collaboration with METEF (The International trade fair for the Aluminum Supply Chain)

Presentation, Progressi nell'ambito del Centro nazionale mobilità sostenibile, Spoke 11. Materiali per alleggerimento., Cluster Lombardo della Mobilità (CML) - Tavolo WG MATERIALI-SPORT-ALLEGGERIMENTO 

L’ultima creazione dell’Università di Bologna, MOST e Onda Solare si mostra per la prima volta a pubblico e stampa, Unveiling di Emilia 5 (Museo Ferrari di Maranello)  

Girelli/Baldi, Progressi nell'ambito del Centro nazionale mobilità sostenibile, spoke 11-UniBs. Materiali per alleggerimento., Cluster Lombardo della Mobilità (CML) - Tavolo WG MATERIALI-SPORT-ALLEGGERIMENTO 

Elena Mingotti, Ottimizzazione del trattamento termico di un getto automotive a parete sottile prodotto mediante pressocolata in lega AlSi10MnMg da riciclo, 37° Congresso tecnico di fonderia - ASSOFOND, Convegno On-line 

Federico Baldussi, Effetto del contenuto di silicio nelle leghe d'alluminio riciclato sulla durata degli stampi e degli inserti da pressocolata, 37° Congresso tecnico di fonderia - ASSOFOND, Convegno On-line 

Omar Bologna, Tecniche avanzate di giunzione per componenti automotive leggeri: caratterizzazione delle saldature di leghe di alluminio dissimili e integrazione dell’additive manufacturing, 37° Congresso tecnico di fonderia - ASSOFOND, Convegno On-line 

Luca Marchini, Danneggiamento da metallo liquido di acciai per stampi immersi in leghe di alluminio a diverso contenuto in lega di Si per pressocolata, 37° Congresso tecnico di fonderia - ASSOFOND, Convegno On-line 

Annalisa Pola, Materiali metallici per una mobilità sostenibile, Presentazione durante il VII Convegno del Dipartimento di Ingegneria Meccanica e Industriale, Università degli Studi di Brescia